Welltech Cooling Systems

Round shape towers are used in all type of industries to cool the re cycle water flow from 200LPM to 1000 LPM. Round Shape will give very good appearance and 100% cooling efficiency. The rotary sprinkler gives uniform water flow over the wet deck fills and gives maximum cooling efficiency.

The Cooling Towers Consists Of Honey Comb PVC Fills In Design That Maximum Economy And Efficiency And Directly Driven Fan And Motor “minimum Drift Losses” Uniform Distribution Of Hot Water By Rotating Arm Sprinkler. Hot Dipped Galvanised Hardware To Withstand Wind Forces. The Bottle Shape Makes Possible To Provide Maximum Cooling Efficiency In Minimum Plan Area With Lower Energy Consumption.

Welltech series counter flow round type cooling towers were strictly examined by "Quality Supervision and Inspection Center of National Glass work" in 2006, the result showed Wellteh series cooling towers completely comply with all national standards. Welltech series counter flow induced draft cooling tower is designed with bottle type structure, so that the volume of prevailing air is minimized. Every part of the cooling tower is designed and made precisely and further permits easy installation and endurance due to light weight and strong structure. The testing report of cooling capacity proves its high efficiency. This series of cooling tower have passed the GB7190.1-1997 quality certification of super low noise.

A cooling tower is an heat exchanger, in which heat is removed from the water by contact between the water and air. The heat transfer takes place through the heat exchange between air and water and also through evaporation of a small part of the water that is required to be cooled. This allows to cool down to a temperature lower than the ambient (default) temperature, this is an advantage compared to dry coolers.


 It is a technically superior and complete one among its peers, with a rotary sprinkler which ensures that not a square inch of the transfer area is left dry. The design of the shell structure facilitates the smooth air draught and prevents any dead air packets. The water basin with the suction tank is scientifically designed so that even when only the suction tank is full the pump with not run dry due to air lock.

We leading manufacturers and exports of 30TR FRP Round shape and square shape cooling tower with PVC Fills to below countries
Bangladesh,
Djibouti,
United Arab Emirates,
Kenya,
Kuwait,
Zimbabwe,
Malaysia,
Nigeria,
Tanzania,
Oman,
Togo,
Zambia,
Mozambique,
Uganda,
Myanmar,
Nigeria

30TR Cooling tower size: 1660 x 2000MM (D x H) with 1HP Motor

Discription: MAKE:WELLTECH
Design,Engineering,Manufacturing,Supply, for MODEL WCS-CO230 FRP Cooling tower Round type with honey comb PVC fills, Water distribution arrangement with Aluminium sprinkler, Statically and dynamically balanced axial flow fan, TEFC motor, Make up and quick fill arrangement, over flow and drain connections with water holding basin. Suitable for flow rate 300L/min, 90,000KCAL/H





The FRP Bottle Shape and Square shape Cooling Towers (Fibre glass Reinforced Plastic) also called as induced draft cooling tower. The casing and basins are designed to withstand severe vibration, high wind load and to resist corrosion. The Cooling Tower consists of Honey comb PVC fills and eliminators in a design that maximizes economy and efficiency and directly driven fan and Motor ''Minimum drift Losses’. Uniform distribution of hot water by rotating arm sprinkler. Hot dipped Galvanized hardware to withstand wind forces. The bottle shape makes possible to provide maximum cooling efficiency in minimum plan area with lower energy consumption.

We leading manufacturers and exports of 15TR FRP Round shape cooling tower with PVC Fills to below countries
Bangladesh,
Djibouti,
United Arab Emirates,
Kenya,
Kuwait,
Zimbabwe,
Malaysia,
Nigeria,
Tanzania,
Oman,
Togo,
Zambia,
Mozambique,
Uganda,
Myanmar,
Nigeria

20TR Cooling tower size: 1300 x 2000MM (D x H) with 1HP Motor

Discription: MAKE:WELLTECH
Design,Engineering,Manufacturing,Supply, for MODEL WCS-CO220 FRP Cooling tower Round type with honey comb PVC fills, Water distribution arrangement with Aluminium sprinkler, Statically and dynamically balanced axial flow fan, TEFC motor, Make up and quick fill arrangement, over flow and drain connections with water holding basin. Suitable for flow rate 250L/min, 60,000KCAL/H





The FRP Bottle Shape Cooling Towers (Fibre glass Reinforced Plastic) also called as Round Shape Cooling Tower. The casing and basins are designed to withstand severe vibration, high wind load and to resist corrosion. The Cooling Tower consists of Honey comb PVC fills and eliminators in a design that maximizes economy and efficiency and directly driven fan and Motor 'Minimum drift Losses’. Uniform distribution of hot water by rotating arm sprinkler. Hot dipped Galvanized hardware to withstand wind forces. The bottle shape makes possible to provide maximum cooling efficiency in minimum plan area with lower energy consumption.

We leading manufacturers and exports of 15TR FRP Round shape cooling tower with PVC Fills to below countries
Bangladesh,
Djibouti,
United Arab Emirates,
Kenya,
Kuwait,
Zimbabwe,
Malaysia,
Nigeria,
Tanzania,
Oman,
Togo,
Zambia,
Mozambique,
Uganda,
Myanmar,
Nigeria

15TR Cooling tower size: 960 x 2000MM (D x H) with 0.5HP Motor

Discription: MAKE:WELLTECH
Design,Engineering,Manufacturing,Supply, for MODEL WCS-CO215 FRP Cooling tower Round type with honey comb PVC fills, Water distribution arrangement with Aluminium sprinkler, Statically and dynamically balanced axial flow fan, TEFC motor, Make up and quick fill arrangement, over flow and drain connections with water holding basin. Suitable for flow rate 200L/min, 45,000KCAL/H

Additional Information:

• Item Code: WCS-CO215
• Pay Mode Terms: T/T (Bank Transfer),Other
• Port of Dispatch: chennai,tuticorin
• Delivery Time: immediately
• Packaging Details: wooden packing

WELLTECH cooling tower manufacturer as customer design as per Cooling Tower 15TR Cooling Tower Welltech 20TR Cooling Tower Welltech 30TR Cooling Tower Welltech 40TR Cooling Tower Welltech 50TR Cooling Tower Welltech 60TR Cooling Tower Welltech 80TR Cooling Tower Welltech 100TR Cooling Tower Welltech 150TR Cooling Tower Welltech 200TR Cooling Tower Welltech 250TR Cooling Tower Welltech 300TR Cooling Tower Welltech 400TR Cooling tower Welltech

Welltech have positioned ourselves as a reputed organization, committed towards offering a wide array of FRP round shape Cooling Tower. The offered cooling tower is designed in such a manner that these have minimum drift losses. Our cooling tower is available in the shape of cuboids and has easy access to the internal components. We assure our clients that our range of machines is quality tested against predefined quality parameters, in order to meet international standards.
Features:
Could easily access the internal component Outstanding performance Highly spacious
SALIENT FEATURES:All structural in HDG Steel to arrest rust PVC Fills with varying flute sizes of 12 mm, 14 mm, 19 mm, 22 mm to increase the contact surface area.TE / TEFC, IP-55 Protected 'F' Class Insulated motor with extended shaft to assist outdoor applications.Adjustable pitch axial flow, dynamically balanced aluminium fans to improve the air exhaust at minimum power usage.Casings of FRP (Fibre Reinforced Plastics) for durability and strength All joints fastened with SS fasteners to arrest rust Uniformity in water dispersion through rotary sprinkler Capacities 10TR to 1500TR , in single cellWater flow 5 m3/h to 1000 m3/h , in a single cell360 °C air intake area assist 100% cooling efficiencyDelta T (Temperature drop) 4°C to 20°C, in single cell ABS Fills for high temperature applications (80 °C)Being Bottle Shape with stands High Wind Velocity.Eliminators are of special F.R.P. design to reduce carryover to the barest minimum.A high efficient nylon rotating sprinkler head system and aluminium alloy sprinkler system is incorporated. Both sprinkler systems are self -rotating at low head loss.The axial flow fiber fan is not only low noise but capable of producing large volume air flowAero - dynamically designed propeller fans at low speed are used to save on per consumption and to assure quiet operation. Fan blade is aluminium alloy fans

This tower design has been developed after detailed research and analysis of the engineering design. The design allows a substantial saving in space, power and water consumption.High Performance Design

Type of cooling towers:

1, square type cooling tower
2, round type cooling tower
3, fanless cooling tower
4, rectungular type cooling tower
5, evaporator types cooling tower
Latest superior computer designed PVC FILLS offer maximum surface area with minimum resistatnce to Air Flow and hence lower power consumption which means lower annual electrical bills. The high efficiency of the fans is achieved by a tapered and aerodynamic design of the fan blades. This dynamically balanced fan assembly ensures smoother operation, longer bearing & motor life. Superior quality of FRP laminates with isothelic resin increases strength of the casing shell which reduces vibrations and it gives assurance of longer tower Life. Neo Penta Glycol (NPG) gelcoat finish assures for UV protection and colour retention with superior surface finish and hence superior asthetic look.Excellent FRP Quality
Superior quality of FRP laminates with isothelic resin increases the strength of the casing which reduces the vibrations and it gives assurance of longer tower life.
Neo Pental Glycol (NPG) gelcoat finish assures for UV protection and colour retention with superior surface finish and hence superior asthetic and elegant look.

We leading manufacturers and exports of Round shape cooling tower to below countries:-

Bangladesh,
Djibouti,
United Arab Emirates,
Kenya,
Kuwait,
Zimbabwe,
Malaysia,
Nigeria,
Tanzania,
Oman,
Togo,
Zambia,
Mozambique,
Uganda,
Myanmar,
Nigeria

15TR Cooling tower size: 960 x 2000MM (D x H) with 0.5HP Motor

Discription: MAKE:WELLTECH
Design,Engineering,Manufacturing,Supply, for MODEL WCS-CO215 FRP Cooling tower Round type with honey comb PVC fills, Water distribution arrangement with Aluminium sprinkler, Statically and dynamically balanced axial flow fan, TEFC motor, Make up and quick fill arrangement, over flow and drain connections with water holding basin. Suitable for flow rate 200L/min, 45,000KCAL/H

Our firm specializes in offering a wide assortment of FRP Cooling Towers. Our cooling towers are manufactured in compliance with the industry quality standards utilizing the top quality material and advanced technology. These cooling towers are appreciated for their high performance, remarkable quality, longer operational life, dependability and low maintenance cost. These cooling towers are used for water cooling purposes in pvc pipe manufacturing plant and foundry industries.

Features:

• Enhanced service life
• Excellent performance
• Perfect finish

Welltech offered industrial application cooling tower which FRP material of 40TR FRP Induced draft counter flow cooling tower wcs co240

cooling tower with PVC Fills to below countries
Bangladesh,
Djibouti,
United Arab Emirates,
Kenya,
Kuwait,
Zimbabwe,
Malaysia,
Nigeria,
Tanzania,
Oman,
Togo,
Zambia,
Mozambique,
Uganda,
Myanmar,
Nigeria

40TR Cooling tower size: 1700 x 2000MM (D x H) with 1HP Motor

Discription: MAKE:WELLTECH
Design,Engineering,Manufacturing,Supply, for MODEL WCS-CO240 FRP Cooling tower Round type with honey comb PVC fills, Water distribution arrangement with Aluminium sprinkler, Statically and dynamically balanced axial flow fan, TEFC motor, Make up and quick fill arrangement, over flow and drain connections with water holding basin. Suitable for flow rate 300L/min, 1,20,000KCAL/H





The FRP Bottle Shape and Square shape Cooling Towers (Fibre glass Reinforced Plastic) also called as induced draft cooling tower. The casing and basins are designed to withstand severe vibration, high wind load and to resist corrosion. The Cooling Tower consists of Honey comb PVC fills and eliminators in a design that maximizes economy and efficiency and directly driven fan and Motor 'Minimum drift Losses’. Uniform distribution of hot water by rotating arm sprinkler. Hot dipped Galvanized hardware to withstand wind forces. The bottle shape makes possible to provide maximum cooling efficiency in minimum plan area with lower energy consumption.

Welltech Key of our products of cooling towers
1000tr cooling tower, 100tr cooling towers, 10TR cooling tower, 125tr cooling tower, 130tr cooling tower, 150tr cooling tower, 200tr cooling tower, 20tr cooling tower, 250tr cooling tower, 25tr cooling tower, 300tr cooling tower, 30tr cooling tower, 350tr cooling tower, 400tr cooling tower, 40tr cooling tower, 500tr cooling tower, 50tr cooling tower, 600tr cooling tower, 60tr cooling tower, 70tr cooling tower, 80tr cooling tower, Adva-tech Engineers, axial cooling fan, Black PVC fills, blue PVC fills, chemical plants, Classik Cooling Towers, Common applications include cooling the circulating water used in oil refineries, cooling tower components, Drift eliminator, Dynamic balanced energy efficient axial type, Energy Efficient Cooling Tower Fans, Fill Size : 600mm x 300mm x 150mm, Fills Flute height 12mm to 19mm & sheet thick 0.2 to 0.25 mm, food processing plants. The PVC Fills offered by us are designed to meet the specific cooling requirements of most cooling towers. The economical and efficient PVC fills have longer functionality and, Honey comb design with double edge folded, JCT Fills for Power Plant, natural gas plant, petrochemical plants, power plants, Precision Cooling System, processing plants, PVC Cooling Tower Fills, PVC fills, PVC fills exporters, Rigid Poly Vinyl chloride, sigma fills, what is cooling tower, Win Equipments

FRP Cooling Tower :

The Round Shape FRP Cooling Tower may call as Bottle Shape . The casing and basins are designed to withstand severe vibration, high wind load and to resist corrosion.

The JC FRP Bottle shape Cooling Tower consists of Honey comb PVC fills and eliminators in a design that maximizes economy and efficiency and directly driven fan and Motor 'Minimum drift Losses'. Uniform distribution of hot water by rotating arm sprinkler.

Hot dipped Galvanized hardware to withstand wind forces. The bottle shape makes possible to provide maximum cooling efficiency in minimum plan area with lower energy consumption.

Specifications of Bottle Shape FRP Cooling Tower

• The Ranges are from 10 TR to 10000 TR.
• Send your requirement to get our best free quote 
  1. Water flow rate, 
  2. Hot water Inlet temperature, 
  3. Required cold water Outlet 
  4. temperature and 
  5. Wetbulb temperature

We are manufacturing a premium range of FRP Cooling Tower by using technically advanced mechanism to improve the quality of products. Made from quality approved raw materials, these are known for their compact design, corrosion resistance and ease of maintenance. Our collection is capable to render the varied requirements of various areas such as chemical plants, power stations, oil refineries and building cooling.

In FRP cooling towers production a special composition of raw materials are selected to withstand corrosion, to resist water borne bacteria and organisms & is light in weight which permits roof installation with special reinforcement of any kind. Vertical induced draft counter-flow design permits installation in any direction with freedom. It consumes less power (energy) overall because of less area.

The round cooling tower is known for its outstanding design and technology. Being it round, the air flow in the cooling tower is evenly distributed. The tower design incorporates hot water inlet at the bottom collection sump flown vertically to the mechanical rotary sprinkler located above the fill media. The inlet water pressure rotates the sprinkler, featuring extended arm pipes with orifices to disperse water uniformly over the fill media. The evaporated water removes the heat from the remaining water. The warm moist air, which is driven through the fan deck will be discharged to the atmosphere.

The stand-out features of the bottle cooling tower are compact design, with varying flute sizes, to offer maximum heat transfer surface per unit volume and contact surface area.

FRP cooling tower meaning is fiberglass reinforced plastic cooling tower innovated in a special way for heat exchange allowing air and water to come into contact with each other to the lower temperature of hot water. FRP cooling tower working is mechanically considered as heat rejection device where wase heat will be rejected to the atmosphere through the aid of a cooling water stream towards a lower temperature.

The FRP Bottle Shape Cooling Towers (Fibre glass Reinforced Plastic) also called as Round Shape Cooling Tower. The casing and basins are designed to withstand severe vibration, high wind load and to resist corrosion. The Cooling Tower consists of Honey comb PVC fills and eliminators in a design that maximizes economy and efficiency and directly driven fan and Motor 'Minimum drift Losses’. Uniform distribution of hot water by rotating arm sprinkler. Hot dipped Galvanized hardware to withstand wind forces. The bottle shape makes possible to provide maximum cooling efficiency in minimum plan area with lower energy consumption.

MATERIALS FOR CONSTRUCTIONQ CASING Cooling Tower Casing is made of selected grade materials of tough Fibre Glass Reinforced Polyester & resins, etc. Additional embossing is done for extra strength in case of big cooling towers. Q SPRINKLER Uniform distribution of water over the honeycomb Fills is achieved by means of automatic water sprinkler. Specially designed rotary sprinkler head is made of PVC/aluminium alloy to avoid corrosion, also fitted with sealed ball bearings to take care of thrust & radial loads. S.S. & Brass sprinklers are also provided at an extra cost. Q ALLUMIUIM FAN Welltech cast aluminium alloy fan is of aero dynamic designed axial flow type to achieve high efficiency. FRP fan set can also be supplied on request at extra cost. Q DRIFT ELIMINATOR CCS Drift eliminators, to reduce carry over losses through of moistures drop in the air stream. The individual drift eliminators of s-shaped corrugated sheets are bonded with subsequent layer to creat the structure. Q PVC HONEYCOMB FILLS PVC Honeycomb type fills having extended contact area. Splits incoming air and water into several streams spread evenly across the water cross section increasing heat transfer rate easy to replace.